VapeWholesaleHubCartridge Supplier Scorecard Template — 2026 Buyer Notes
Everything below applies whether you are ordering one mixed carton or a full container. The numbers scale, but the logic does not change, which is the point of writing it down once.
How Cartridge Batches Are Checked
Set the cartridge complaint threshold in the contract before you need it. Deciding what counts as an acceptable defect rate during a dispute is the worst possible time to negotiate it.
Train whoever receives cartridge cartons to note anything unusual at the point of unloading. Damage discovered at the dock is a freight claim; damage discovered a week later is your problem.
- Plan the switch from air to sea freight before you need it.
- Check carton dimensions against your freight quote before confirming.
- Rotate stock by batch code rather than by delivery date.
- Keep sealed retained samples from every production batch.
- Agree the tolerance band in writing before approving artwork.
Freight, Customs and Timing
Model cartridge freight both ways before choosing a method: cost per unit and cost per week of delay. The second figure is the one that decides whether a cheap option was actually cheap.
Selling Cartridge at Store Level
Rotate cartridge facing rather than price for the first month. Visibility changes sell-through more reliably than a small discount, and it does not train customers to wait for offers.
Where Cartridge Sits in the Range
A tight cartridge range with deep availability usually outsells a wide range with thin stock. Customers who find their line in stock come back; customers who are told to wait do not.
Reading a Cartridge Spec Sheet
A written cartridge specification should be short enough to read in a minute and precise enough to argue about. If a factory cannot confirm a number in writing, assume the number is whatever is cheapest that week.
| Product category | Disposable |
|---|---|
| Resistance band | 1.2 - 1.4 ohm |
| Capacity tolerance | +/- 5% |
| Puff count method | Machine cycle 3s on / 27s off |
| Master carton | 120 units |
| Carton weight | 9.5 kg |
| Shelf life | 12 months |
| Storage | 15-25 C, dry, away from direct light |
What Cartridge Really Costs Landed
Margin on cartridge is rarely lost at the till. It is lost through dead stock, returns and emergency air freight. A slightly higher landed cost with predictable lead time usually beats the cheapest quote on the spreadsheet.
Indicative reference points for planning purposes: entry tier from USD 1.24 per unit at 2000 units, mid tier at USD 0.70, and volume tier at USD 0.55 for full container quantities. These figures move with specification, packaging and freight, so treat them as a shape rather than a quote.
Practical Checklist
- Keep sealed retained samples from every production batch.
- Agree the tolerance band in writing before approving artwork.
- Rotate stock by batch code rather than by delivery date.
- Write the complaint threshold into the order terms.
- Start with a mixed carton and let your own sell-through decide.
- Ask how the factory measures puff count, then compare like with like.
Frequently Asked Questions
Can you match an existing product I already sell?
Often yes, provided we can measure it properly. Send a physical sample and we will report back on what can be matched, what will differ slightly, and why. An honest gap is more useful than a vague promise.
Can I mix strengths in one order?
In most cases yes, as long as each strength meets the minimum run length. Mixed strength cartons are popular with retailers building their first display because they show the full ladder without over committing.
What information do you need to quote?
Target specification, approximate quantity, destination and any packaging requirement. With those four we can usually come back with a costed option the same working day rather than a request for more information.
Can the packaging be customised?
Yes. Most cartridge programmes use private label packaging once volumes justify the printing plate. We supply dielines, check your artwork for print issues and hold approved files so reorders need no new setup.
Can I visit the production facility?
Yes, and we encourage it for larger programmes. Visits are most useful when you already have a draft specification, because you can then check the specific processes behind the numbers you care about.
Next Step
The best cartridge programmes we see are run by buyers who write things down. Specifications, batch records, complaint thresholds - the paperwork is the advantage.
Related Reading
- Cartridge Reorder Discipline for Busy Distributors — Private Label Programmes
- Cartridge Trade Credit and Account Terms — Three Price Tiers
- Cartridge Lead Time Buffers That Actually Work — Regional Distributors
- Where Cartridge Fits in a Balanced Vape Assortment — Small Batch Buyers
- Cartridge Shelf Rotation for Multi Site Retailers — Step by Step
- Cartridge vs Standard Alternatives: What Changes for Your Shelf — the Buying Desk